Luxman L-550ax Mark 2 novi je model za 2017 godinu.
Luxman L-550aX Mark 2, integrirano je pojačalo u čistoj A klasi, koje se pritiskom tipke pretvara u izlazno pojačalo ili predpojačalo, te je u stvari kombinacija tri aparata. Kada spomenemo implementiranu gramofonsku sekciju za MM ili low output MC zvučnice, te ulaz za slušalice, jasno je da se radi o nevjerojatno opremljenon i fleksibilnom uređaju visoke klase. Naravno, sa naglaskom da se radi o pravom Luxmanu gdje je kvaliteta zvuka i izrade na prvome mjestu.
L-550AXII is the Mark 2 version of the L-550AX which was originally launched in 2011. The L-550AXII makes its debut featuring a high-precision discrete electronic attenuator (LECUA) and the latest version of Luxman’s proprietary high sound quality feedback circuit ODNF 4.0, both of which are used in Luxman’s upper range amplifiers.
Keeping the classic appearance with traditional VU meters on the front panel, using trickle-down technology from the development of the flagship integrated amplifier L-590AXII. The L-550AXII now enjoys dense tonal color particular to pure A class sound and more detailed reproduction of the low frequencies as well as the ability to drive more difficult speaker loads.
Chassis bases have superb vibration absorption in order to suppress noise levels. The power transformer, electrolytic capacitors and amplifier output stage (see amp block below) are laid out so as not to interfere with each other. To reduce interference further, the block construction isolates each section using shielding panels, and extensive internal filtering to reject magnetic flux interference.
Pure Class A
Thanks to the always-on nature of the topology and the removal of an entire type of distortion, allied to sound that excels in a mid-range liquidity, low-level detail, superb dynamics and transparency, its devotees are more than happy to put up with low efficiency and heat. What Class A always seems to offer above everything else is a tube-like sound without the maintenance hassle of tubes.
The L-590Ax, L-550Ax and the L-509u, feature the new high quality electronic selector switch, which is the heart of the C-1000f pre-amp (one of Luxman’s 80th anniversary commemoration models). The sound quality deterioration using the new electronic input switch is now minimal, while channel separation and crosstalk efficiency were raised substantially in comparison with the L-550A / L-590A. In addition the illuminated position indicator around the input selector knob, makes it much easier to view the selected position even from afar.
The integrated amplifiers also benefit from the C-1000f in that they use a variation of the LECUA 1000 volume control. At any single volume setting only a few resistors are in circuit per channel. The less devices in the signal path, the purer the sound, the cleaner the music.
At low listening levels, potentiometers have trouble keeping both channels in balance, so one channel might easily be 3dB louder than the other. With the volume control made of discrete parts, this is no longer an issue.
The amplifier section has not been ignored either; noise and distortion has been kept to a minimum with the introduction of ODNF version 3.0A. The deep, rich Class A tone is available here is Luxman’s hall-mark sound. More info on ODNF below.
Pure Copper Cabling
Extensive listening was applied to the high purity, oxygen free copper (OFC) cables which are used to transmit the signal throughout the amplifier. These cables have a minimal audible signature and minimal electrical effect on the audio waveform. Linear wide bandwidth frequency response is achieved by the low measured values of both inductance and capacitance. The result, the cables do not color the sound, but pass it through, quickly.
Enjoy the ability to play or record your LP collection with the built-in phono stage which accommodates both Moving Magnet and Moving Coil cartridges. The MM input has approx. 35dB of gain. While the MC input has 55dB of gain (a multiplication of 550x). We recommend MC cartridges with an output >.25mV. Lower than that you might consider using the MT-88 moving coil step-up transformer.
The L-550Ax has a new improved phono stage—quieter, more detailed and yet as rich and musical tonally as Luxman is famous for.
A subsonic filter is also easily accessible from the remote control in order to remove unwanted low frequency noise while you are listening to a record. When the stylus hits the groove, you might notice the woofers modulating in and out, even though there is no music playing yet. This is due to the ultra low frequency information (below the music), this unnecessary information places a strain on the amplifier and is best filtered out. A mono switch is also available for both loudspeaker setup as well as mono record playback.
There is also a high quality headphone amplifier, accessible from the front panel, ideal for late night listening. You can turn off the speaker output by a simple click of the Speaker Selector.
The headphone outlet sees the same signal as the speaker terminals, there is one resistor per channel in the signal path to pad down the output.
Two Pairs of Speaker Terminals
Large speaker terminals for driving two individual sets of speakers. At the turn of the speaker switch, it is possible to change between the two pairs of speakers easily. In addition, if the A+B function is used; Takasina capacitors are used to parallel the output which permits bi-wiring a single pair of speakers.
Luxman holds many patents for audio engineering, amongst them is the application of Global Negative Feedback to the output stage, which while widely used throughout the audio industry, they no longer use themselves.
Today, Luxman uses a distortion reduction circuit called Only Distortion Negative Feedback (ODNF). This system works by isolating noise & distortion at the output from the music signal and sparingly applying negative feedback to suppress them. Conventional negative feedback systems can have an adverse effect on the music, introducing phase distortion. “The circuit features such an ultra wide range, ultra high slew rate and ultra low distortion that it does not use phase compensation for the music signal amplifying circuits.” This new technology also ensures that need for a DC servo circuit is alleviated, again improving sound quality.
Now with version 3.0 three different monitoring passes are made of the audio signal, to eliminate any noise or distortion in the music signal. It results in a lower noise floor of about 2 dB, giving you blacker silence between the notes and a more dynamic performance.
The tone controls might seem like an anachronism in this day and age of minimalism, but they can be remarkably effective in bring to life a less than perfect music collection. We all have music gems in our collection that are sonically challenging. A lot of the 1980’s CDs are quite harsh sounding and the digital glare can be quite fatiguing. Reduce the treble slightly and while the harsh CD is not going to suddenly sound like a reference recording, at least it will now be perfectly listenable. Sit back relax, enjoy the music & forgot about the Hi Fi. When you want to bypass the tone controls, just engage the Line Straight switch, either from the remote control or from the front panel.
|Rated output||20W + 20W (8Ω), 40W + 40W (4Ω)|
|Input sensitivity / input impedance||PHONO (MM): 2.5mV/47kΩ
PHONO (MC): 0.3mV/100Ω
|Output voltage||RECOUT: 180mV, PRE OUT: 1V|
|Frequency response||PHONO: 20Hz to 20kHz (±0.5dB)
LINE: 20Hz to 100kHz (+0, -3.0dB)
|Total harmonic distortion||0.007% or less (8Ω, 1kHz)
0.02% or less (8Ω, 20Hz to 20kHz)
|S/N ratio (IHF-A)||PHONO (MM): 91dB or more,
PHONO (MC): 75dB or more
LINE: 105dB or more
|Volume adjustment||New LECUA1000|
|Amplification circuit||ODNF 4.0|
|Output configuration||Bipolar parallel push-pull|
|Max. amount of tone control||BASS: ±8dB at 100Hz
TREBLE: ±8dB at 10kHz
|Power supply||230V~(50Hz) / 115V~(60Hz)|
170W (under no signal), 0.5W (at standby)
|External dimensions||440(W) x 178(H) x 454(D) mm
front side knob of 20mm and rear side terminal
of 27mm included in depth
|Net weight||24.3kg (main unit)|
|Accessories||Remote control (RA-17A)
|Speaker terminal Supported Y-lug terminal dimension||Width of part a: 15mm or less
Width of part b: 8mm or more
* Connection may not be performed
depending on the shape of the